The Wismec RX2 21700 is the latest mod in the Reuleaux series from Wismec. It’s almost identical to the RX2 20700 but with a bigger battery door to fit 21700 batteries. And it keeps in line with the original triangular shape of the RX2/3 mods.
Price: ~ $50
Colors: gloss black, gradient white, gradient purple and gradient green
The RX2 21700 has a nice shape to it and feels pretty solid without being too big. Again, it’s pretty much the same form factor as the RX 20700 and it uses the same large and elongated hexagonal firing button, and it’s got the same menu layout of the Gen 3. But in general, there’s nothing really new here.
I test all mods using an oscilloscope to find out if their ratings are accurate, and how precise and consistent the mod is. Testing for this mod was done with iJoy 5-leg 20700 batteries, since they’re better than the included pair of batteries. When fully charged, the iJoy batteries are above 4.0 V per cell.
Just because a mod is capable of producing over 200 watts doesn’t mean I recommend people vape at such high wattages. This is done in a controlled testing environment and I’m aware of the risks involved and take appropriate precautions. I don’t recommend vaping over 150 watts on a dual-battery mod. Always use authentic 20-amp CDR or higher batteries.
This mod is accurately rated for wattage it can handle. It was able to produce 234 watts with a 0.2-ohm coil, so it exceeds the 230 watts listed. As far as voltage goes, I was able to get 9.046 V with a 0.5-ohm coil so it meets the listed 9 V, and I was able to determine that it has a boost circuit.
The RX2 21700 is listed at 50 amps, like many other Wismec mods. But the results showed it cannot do 50 amps. I was able to get 40 amps max from this mod with a 0.12-ohm coil (at 195 watts). That’s pretty average these days for a dual-battery mod, so no big complaints so far — but they clearly overstate its amp capabilities.
The Wismec RX2 21700 can meet most of its promised output, but it’s too inconsistent for me to assign any numbers to it in good conscience. During my normal usage of the mod, I found that sometimes it would fire fast and hard, while other times I noticed a fire delay or a weak hit. It was pretty rare for me to be able to vape normally and get the same puff each time. It’s a common issue with the RX line of mods that I’ve run into before. More on that in a bit.
During my testing to see what the chip actually does, I created a list of issues that I found. (Note: I had the pre-heat function turned off throughout this testing.)
So, what’s the cause of all this? In my experience the one thing all these mods have in common is that they use the actual body of the mod as the ground. Most mods use a wire that is soldered onto the ground of the 510 pin internally, and then soldered into the common ground on the chip itself.
In the case of this mod and quite a few other Wismec mods I’ve tested — like the RX300, the Predator, and the RX Gen 3 — they all had a similar grounding system. The way it works with the RX2 21700 is that the 510 negative threading is secured into the mod, and the body itself has two screws that secure the chip in place. These two screws are located inside the bottom of the mod underneath the batteries.
After removing one screw, the mod still worked, but resistance changed. When removing both screws, the mod reads a short and won’t fire. When both screws are loose, the mod still works, but reads resistance very inaccurately. The fire button is also screwed into the mod which could be the cause of the “hot button,” like you get on mech mods with dirty or poor contacts.
I hope Wismec changes this in the future. They should take it seriously and use the information I’ve provided here to make better products.
As a reviewer it’s my duty to inform the public and give a fair assessment of devices, because in the end it benefits everyone. It allows companies to fix mistakes and to make better products. It also helps vapers avoid wasting money or getting a device that frustrates them, which might cause them to go back to smoking.
For temperature control, I’m going to keep this short and sweet. The mod is very inconsistent, and most of the time it winds up kicking you out of TC mode anyway. It’s pretty much not usable as a temp control mod at all.
The mod follows the standard five clicks to turn on and off. Outside of that, it’s the same old clunky menu system from the previous RX mods. I find it to be outdated and not very user friendly. If you are used to it, it’s probably not going to be a big deal, but if you are new to the RX menu system, it’s going to take time to adjust.
Use three clicks to enter the “menu,” which really isn’t a menu. It will start blinking to indicate what settings you can change. You use plus to cycle through modes, and minus to drop down and cycle between other options like locking the coil, changing power in temp mode, and resetting the puff counter. Holding plus and minus together locks the adjustment buttons. Holding minus and fire toggles stealth mode. Holding plus and fire enters the menu to turn the logo on and off, set up the pre-heat, and screen timeout.
So, can I recommend the Wismec RX2 21700? If you have to ask, you probably didn’t read the review carefully. The answer is definitely no! There is no way in good conscience I could sign off on this mod. I hope that Wismec takes this feedback seriously in order to make better products in the future that I can recommend to vapers.